How to Use the Crawler Bulldozer Not Easy to Malfunction?

 Today Bulldozer China Factory introduces the correct way to use the crawler bulldozer.


1.Speed change and retreat

When shifting gears, the throttle handle should be pushed forward to the low-speed idling position, and then the main clutch lever should be pushed to the front to disengage the main clutch. Due to the small brake in the main clutch, the power input shaft of the transmission stops rotating. . At this time, you can correctly shift the shifting benchmark to the required gear, and then put the forward and backward lever to the forward or backward position (when the bulldozer is forward, pull the forward and backward lever back, and push it forward when back). After being in gear, pull the throttle handle backwards to increase the engine speed, and connect the main clutch smoothly, and the bulldozer starts running.

When the bulldozer is driving, the main clutch lever should be pulled to the rear, not in the semi-engaged position. Because the main clutch is half-engaged, friction plate wear will be aggravated. Bulldozer transmissions generally have five forward gears and four reverse gears. The forward and backward lever can be used to change the direction of the bulldozer.

When the bulldozer is operating, it should run at the highest speed as possible to improve the operating efficiency. However, the driver should always pay attention to whether the engine is running normally. When the engine is overheated and the exhaust smoke is found, the speed should be appropriately reduced.


2. Steer

When the Crawler Dozer is turning, the steering clutch lever on the steering side can be pulled back to disengage the steering clutch, so the track speed of the corresponding side becomes slower, and the bulldozer starts to turn. In order to make the bulldozer make a sharp turn, in addition to disengaging the steering clutch, the corresponding brake pedal should be depressed. Generally, the sharp turn is allowed only when the first gear is running. When the brake is not used, the foot should not be placed on the brake pedal, otherwise it will cause wear of the brake belt and increase fuel consumption.

When the bulldozer is turning, step on the brake pedal smoothly to avoid jumping when turning. After turning, release the brake pedal and release the joystick. If the turning radius is large, it is not necessary to step on the brake pedal. When you don’t want to, don’t make the bulldozer turn in place at high speed, so as to avoid the accident caused by the track derailment.


Crawler Dozer


Crawler Dozer


3. Drive on the ramp

Different types of bulldozers have different climbing capabilities (generally 30 °), and the slopes and terrains that can be adapted by bulldozers of the same structure are also different. The driver should be familiar with the climbing limits of the model used to avoid landslides due to insufficient uphill and downhill capabilities.

Before going uphill, you should choose the appropriate speed gear according to the terrain, slope size and length, and you are not allowed to change gears during climbing. When going uphill, the bulldozer should run at a perpendicular angle to the hillside, and no horizontal driving is allowed on steep slopes; the blade can be lowered appropriately to avoid affecting sight, and in the event of a landslide, the blade can be quickly grounded to help the bulldozer Brake; if the engine stops on the way uphill, the fuel supply should be stopped immediately, the blade should be lowered and the brake should be applied immediately. If you cannot stop on the slope, you should change the reverse gear and slowly slide to the bottom of the slope (while braking and sliding), and then start the ground to persuade; if you do not stop the fuel supply and slide down in the forward gear, it will be transmitted to the back due to power. The engine caused a reverse fire, causing the air cleaner to inject fuel. In case of reverse fire, close the throttle quickly and brake the bulldozer. Before restarting, check that the shift lever is in the neutral position. When the bulldozer goes downhill, the low speed and small throttle position should be selected, and the brake pedal should be used.


The above are several ways to use the tracked Dozer, which can effectively avoid failures.

评论

发表评论

此博客中的热门博文

Reasonable Operation Of Track Bulldozer

图片
The  Track Bulldozer   has the greatest influence on the transmission oil temperature due to the external resistance and the maximum output torque during the shovel operation. If the small throttle is used for a long time to operate the torque converter in the inefficient zone, the transmission oil temperature will rise. If the large throttle is used during frequent shifting, it will cause severe impact on the machine and increase the temperature of the transmission oil. To this end, the operator should reasonably control the amount of bulldozer and the timing of the blade lifting and lowering. The soil feeding distance should not be too long, so as to prevent the use of small throttle for a long time. We are  Track Bulldozer Supplier , specializing in the production of machinery and equipment, welcome to consult and order.
阅读全文

How to Choose the Right Bulldozer?

图片
  Purchasing a bulldozer is a significant investment, whether you're in the construction business or need one for specific projects. To ensure you make an informed decision and get the   right bulldozer   for your needs, here are four essential tips and things to know before buying one: 1. Define Your Requirements and Applications The first step in   buying a bulldozer  is understanding your specific requirements and applications. Consider the following: Size and Capacity:  Bulldozers come in various sizes and capacities. Determine the size that can handle your typical projects and the type of material you'll be moving. Attachments:  Many bulldozers can be equipped with various attachments, such as blades, rippers, and winches. Assess which attachments you need for your tasks. Terrain:  Consider the type of terrain you'll be working on, as this can affect the tracks or tires your bulldozer should have. Understanding your specific needs will help you narrow down your options
阅读全文

No Steering Failure of Crawler Hydraulic Steering Bulldozer

图片
  During the use of the bulldozer, due to various reasons, the bulldozer is difficult to turn, cannot turn, cold cars can turn, hot cars can not turn. After the occurrence of these failure phenomena, according to the use time of the bulldozer and the occurrence process of the failure, the classification analysis should be carried out to check the truth, which can avoid unnecessary disassembly and reduce the internal pollution of the machine. The following   Bulldozer Suppliers   introduce common fault phenomena such as bulldozers and related knowledge of inspection and elimination. When the  Dozer  is in use, it suddenly fails to turn on both sides. The overflow valve at the oil inlet of the directional control valve assembly can be disassembled. The reason is that the oil is too dirty, the impurities in the oil wear or strain the surface of the overflow valve core and the inner cavity of the valve body, so that the valve core is stuck in the position where the oil return is turned on,
阅读全文